The 2-Lever Great Grips are grasping aids for a door knob designed for use by individuals with arthritis, grasping disabilities, or upper extremity neuromuscular disabilities. Designed for round or awkward door knobs, this device has two flat levers that extend from opposite sides of the grip. The levers that are intended to make it easier to turn door knobs with a closed fist, elbow, or even a single finger. The Great Grips are made of soft material that easily stretches to fit the knob and bec
The ABLEWARE Door Knob Gripper is a grasping aid for hand designed for use by individuals with arthritis of the hand or fingers or other grasping disabilities. The Gripper fits over round door knobs and outdoor water faucets. The outside is smooth to the touch and the inside is ribbed to firmly grip the door knob. With this device, knobs can be turned with the stroke of the hand, and no hand strength is required.
The Ableware TKO Turning Knob Operator is designed to assist individuals with limited manual strength or dexterity to grasp, turn, and open any non-round control knob or appliance handle. The turner consists of a large T-handle attached to a large round base with retractable pins on its bottom. When the turner is pressed onto a knob the pins contacting with the knob’s surface retract, while the remaining pins surround the knob for a secure grip. The turner can be used on irregular knobs, includi
The Accessible Entry System, model AES 2000, is a building entry system designed for use by individuals who are blind or have low vision. The system includes a large print and voice output tenant directory with both written and verbal operating instructions. The system's visual display uses half-inch high black characters against a back-lit green background. The system incorporates the etched tactile diamond shaped EZ Help system developed by the University of Wisconsin TRACE Center. Pressing th
Handicap accessible thresholds made of mill aluminum, anodized dark bronze alluminum, or mill brass, with various treads. DIMENSIONS: Thresholds have a maximum center-threshold height of 0.25, 0.31, 0.5, or 0.63 inches, with lengths of 2.5, 3, 4, 5, 6, 7, or 8 inches.
The ADA EZ is a powered door operator designed for use doors at institutions and other high traffic areas that are manual opened and closes but occasionally require automatic operation. Upon installation, the unit determines the door's size and weight and automatically tune its controller to operate within ANSI 156.19 and 117.1 standards for door openers and closers. The ADA EZ also has adjustable speed, hold-open time, and opening/closing force. On-board diagnostics continually maintain control
The ADA Ramp Threshold is a threshold ramp designed to provide wheelchair access for individuals with lower extremity or mobility disabilities or spinal cord injury. Model 442S provides a 1:12 slope from the floor to a point 0.5 inch higher. Model 443S provides a 1:12 slope starting from the edge of a threshold. Model 444S is a combination of 442S and 443S. Made of mill finished anodized aluminum, the ramp comes with ten 1.5-inch flat head wood screws. OPTIONS: Sure-Step non-slip abrasive coatin
--- "DO IT YOURSELF" ENTRY ------- PURPOSE: Device to push or pull a door shut from a wheelchair. Aid made of a piece of broom handle or dowel with a crutch tip on one end and a leather loop at the other, which can be hung on a hook by the door. The leather loop hooks around the doorknob to allow the door to be pulled shut without a lot of maneuvering of the wheelchair. SKILLS REQUIRED: Assembly. AUTHOR: Independence Factory TITLE: How to Make it Cheap Manual: Volume 2 REF: Middletown, Ohio: Ind
DO IT YOURSELF ENTRY PURPOSE: To assist individuals with upper extremity and mobility disabilities in activating a large-button powered door operator. Resembling a baton, this device is made from a wooden cylinder with a section cut from a bicycle handlebar grip covering the end used to push the activator button. The ADO is attached to the side of the door operator pad/button using Velcro. DIMENSIONS: 12 inches long x 0.75 inch in diameter. SKILLS REQUIRED: Basic shop skills with a table saw.
The Aluminum Threshold Ramp is a threshold ramp designed for use by individuals who use wheelchairs or scooters. The ramp is manufactured of anodized aluminum and trimmed at the edges with a coarse finish strip to prevent the risk of slippage. The treads are slotted to facilitate drainage and stop the build up of ice. It is also transportable in the back of a car. DIMENSIONS: 2 or 3 feet long.
The Aluminum Threshold Ramp is a threshold RAMP designed to make doorways accessible to individuals who use wheelchairs or scooters. This aluminum ramp has an anti-slip, high traction sandpaper surface. The ramp has mounting holes in its top corners and comes with hardware to secure it to the doorway surface. DIMENSIONS (LxW): 8, 10, 12, 16 or 24 x 32 inches or 16 or 24 x 36 inches. The rise is 0.25 to 0.5, 0.5 to 0.75, 0.75 to 1, 1.5 to 2, or 1.5 to 3 inches depending on length. WEIGHT: 3 to 15
The Ambidextrous Lever Handle, model 7055, is a keyless exterior door lock with lever designed for use by individuals with fine motor, grasping, or upper extremity disabilities. This heavy-duty door lock has an eight-button combination pad with an ambidextrous lever for right- or left-hand doors. The lock has double push capability, meaning a repeated digit can be used in the combination. To preserve the lock's mechanical functions, its inner parts are Teflon-coated. A hold-back feature allows t
The Arrow Q Series Lever Lockset is an exterior door lock with lever handle designed for use by individuals with grasping or upper extremity disabilities. Levers are pressure-cast zinc with a brass or bronze rose, and are non-handed to operate bi-directionally. The lockset is through-bolted, requiring a door from 1.75 to 2 inches thick with a 2.13 inch diameter bore through the door. An extra long bearing sleeve offers added support for interlocking tubes and provides extra lever rigidity. The l
The Arrow W Series Lever Lockset is an exterior door lock with lever handle designed for use by individuals with grasping, fine motor, or upper extremity disabilities. The non-handed lever comes in Broadway, Sierra, or Ventura styles, and is set in a circular plate (rose) assembly. The lockset includes a solid brass, six-pin cylinder with Arrow “A” keyway; a brass latch with brass, bronze, or stainless steel latch front; thru-bolts with support plates; and two six-pin nickel silver keys. DIMENSI
The Arthritis Daily Helper Kit, model 557183), combine products designed for use by individuals with arthritis, fine motor or grasping disabilities or limited hand dexterity. Intended to assist arthritis sufferers with daily tasks, this kit features the following item: Dr. Grip Pen, Rubber Doorknob Extension, EZ Key Turner, Button Hook with Zipper Pull, and Shoe Buttons (see separate entries).
The Astro-Swing, models 2511, 2553, 9331, 9342, and 9553, is a powered door operator that can be used on side hung or center pivot doors, in new or existing installations, inside or outside. Opening time is 3 to 5 seconds, and can be adjusted up to 30 seconds. Doors open to a 90-degree angle, closing with spring action, and exerting less than 15 pounds of pressure. For safety, the door will stop if obstructed. Models include concealed overhead mount, single door (2511); concealed overhead mount
The Auto-Equalizer, models 2610, 4810, 4820, and 4840, is a powered door operator designed to make doors accessible to individuals with physical or mobility disabilities. This heavy duty, low energy pneumatic automatic door operator can be used on new or existing doorways. It opens interior or exterior doors automatically to 90 degrees when actuated, and holds the door open up to 30 seconds. Unit mounting options include a frame (2610), hinge side mount (4810), top jamb mount (4820), or parallel
The Automatic Balanced Door Operator is a powered door closer designed for installation on existing balanced doors. The device operates by means of a motion detector or a push button.
Electric automatic door opener. Available for swinging doors, sliding doors, or conversion units for existing doors. Modular, self contained electromechanical operators fit into door header. Electronic control unit regulates operating mechanism. Sealed mechanical gear drive system with spring and safety clutch for door closing. Built in emergency reverse swing feature. Low noise level. Operates indoors or outdoors in temperatures -30 to 160 degrees Fahrenheit. All models activated by carpet swit
The Bariatric Threshold Ramp is an accesible threshold designed to make doorways accessible to individuals who use wheelchairs or scooters. This bariatric threshold ramp is made of lightweight aluminum with an anti-slip, high-traction sandpaper surface. It covers a threshold rise of 1.5 to 3 inches (model BTR 1636) or 2 to 4 inches (model BTR 2436), and comes with mounting holes and the hardware needed to secure it to the door molding. DIMENSIONS (LxW): 16 or 24 x 36 inches. CAPACITY: 800 pounds
--- "DO IT YOURSELF" ENTRY ------- PURPOSE: Curtain used instead of a door to allow a wheelchair through the doorway. Bathroom (or other) entrance widened by removing the door and installing an expansion rod, with material soft enough to gather and heavy enough to ensure privacy hung from it with shower rings. The curtain can be drawn back and held open with a tieback fastened with velcro. Includes drawings. SKILLS REQUIRED: Sewing. Assembly. AUTHOR: Hamilton, L TITLE: Why Didn't Somebody Tell M
The Besam Electra 150 Series are commercial powered door operators suitable for residential use on standard or swinging doors, both inside and outside. The units are available with remote control, key controls, push button, sensor, elbow switch, contact mats, or kick plate switchs. Hold open time is adjustable from 0 to 30 seconds. An optional security lock when power is on is available. POWER: 110 volt 4 amp. If power fails, 14 pounds of force are required to open the connected door. DIMENSIONS
The Besam Powerglide 4000 Automatic Sliding Door System is a powered door operator system that can be installed in new or existing installations on interior or exterior doors. The operator is mounted on a frame, which is supplied with the unit. FEATURES: Opening time is adjustable from 0 to 5 seconds; hold open time is adjustable from 0 to 45 seconds; door automatically stops if obstructed; and security lock when the power is off. If the door is locked and the operator is activated, the operator
BETAdoors are automatic opening and closing doors that allow hands-free operation in commercial or residential buildings. Specifically, they are electric powered roller blind mechanisms that are self-contained in vertical aluminum frames. Low voltage floor mats, electric eye sensors or push buttons trigger the doors to operate. BETAdoor is available in single (160 Watts), double (320 Watts), 3-way (480 Watts), and 4-way (640 Watts) models. All models available in wheelchair dimensions. BETAdoors
BigBell Basic and BigBell XL are accessible doorbells designed for use by individuals with upper extremity or severe physical disabilities or spinal cord injury. This wireless doorbell features an oversized touch pad button marked with the universal access symbol and is designed to enable individuals with disabilities to summon entry assistance when a powered door operator is not available. BigBell has a range of 100 feet from touch button to receiver. BigBell XL has a range of 600 feet, and als
The BigHorn Plastic Threshold, model BHR1110, is a threshold ramp designed for use to make doorways accessible to wheelchair users. This threshold is slip resistant and can support a heavy load. Made from recycled plastic, it can be vertically cut for height and notched for door molding with typical rotary saws. It has molded miter ends and comes with high grade butyl rubber peel and stick tape for installation. OPTIONS: Shim kit to accommodate rise up to 2 inches. DIMENSIONS (LxW): 12 x 42.75 i
The BIME Wander is designed for use for individuals with dementia. It is a reminder system to encourage time orientation for people with dementia by using verbal messages. It uses reliable and inexpensive technology that can be installed to suit the needs of individual situations. The system is easy to install requiring no technical input. The verbal message is recorded and the minder is placed at the approach to the doorway. It can be left freestanding or hooked onto the wall. Users can use bat
Biolock 333 is a fingerprint door lock with remote control and a lever handle, designed for use by individuals with fine motor or grasping disabilities. This remote-controlled fingerprint lock for single-latch doors has a programmable LED control with storage for up to 99 users, a 500-dots-per-inch optical fingerprint reader, CMOS image sensor, and a reversible lever handle that can be installed to the right or left. The lock has three levels of administrator security which allow the administrat
The Bridge Threshold Ramp is designed to provide wheelchair or scooter access over single steps or doorways. The ramp is made from aluminum with a non-slip surface. OPTIONS: Light duty plate for creating a bridge between the ground and doorway threshold. DIMENSIONS (LxW): 8 x 36 (model TR1), 10 x 36 (model TR1.5), 14 x 36 (model TR2), or 18 x 36 inches (model TR3). Rise is 1 inch (model TR1), 1.5 inches (model TR1.5), 2 inches (model TR2), or 3 inches (model TR3). CAPACITY: 750 pounds.
The Bumper Threshold, model 477S, is a threshold ramp designed for use in emergency exits to allow wheelchair users to exit a room while not allowing entrance. The threshold is made of aluminum with a vinyl, neoprene, EDPM, TPE, silicone or pile insert, and comes with 10 1.5-inch wood screws. OPTIONS: Sure-Step non-slip abrasive coating; other screw types or anchors. DIMENSIONS (HxW): 0.5 x 5 inches. COLOR: Mill finish aluminum, dark bronze anodized aluminum, or gold anodized aluminum.
The Butt Ramp is a portable threshold ramp designed for use by people who have lower extremity or mobility disabilities or spinal cord injury and others who use a wheelchair. It is intended to help a person to get over thresholds or to get on or off of a curb. This straight aluminum ramp has a low rise and is available with wheel guards on both sides or on the left or right side only. The high end of the ramp butts up against the wall under the threshold, and it is raised by legs. The lower end
The Enablers Doorknob Gripper, model EN19CRD, is a door knob accessory designed to assist individuals with limited hand strength or geasping ability in turning standard round door knobs. This glow-in-the-dark gripper slips over the existing knob to provide a slip-free surface. DIMENSIONS: 1.5 inches long x 2.13 inches in diameter.
The Carpet Threshold, models 503S, 504S, 505S, 506S and 508S, is a threshold ramp designed for use to allow wheelchair users to move between carpeted areas. The threshold comes with 10 1.5-inch wood screws. OPTIONS: Sure-Step non-slip abrasive coating; other screw types or anchors. DIMENSIONS (HxW): 0.875 x 2 inches (model 503S); 0.5 x 2.13 inches (model 504S); 0.45 x 0.81 inches (model 505S); 0.81 x 4 inches (model 506S); 0.69 x 1.81 inches (model 508S). COLOR: Mill finish aluminum, dark bronze
The Cherry / Oak / Walnut ADA Compliant Interior Threshold is a threshold ramp designed to provide access for wheelchair users and others with mobility, lower extremity, or walking disabilities. The ramp slopes up both sides gradually, to allow wheelchair users to roll over, and also to provide less obstruction for individuals with walking disabilities. This wooden ramp is available in cherry, oak, or walnut. DIMENSIONS (HxLxW): 0.5 x (24, 36, 48, 60, or 96) x (3.5, 4.5, or 6.5) inches.
The Commander Automatic Door Opener is a powered door opener and closer designed for use by individuals with physical disabilities and wheelchair users. This unit can be used in residential or commercial settings to convert new or existing swinging doors to automatic operation without modifying existing door frames. It works with both in-swing and out-swing door configurations. It can also be used on wheelchair lifts and elevators. The opening speed and hold open time are both adjustable. A cons
The Commercial Gentleman Public Access Door Operator is a powered door operator kit designed for use in public settings to provide barrier free access for people with mobility issues. The operator allows manual use of the door by those not requiring the automatic opener. This operator can be totally pneumatic in operation or interfaced with low voltage (wired or wireless) electronics for total public access. Standard Kit Includes - Commercial Opener & mounting hardware, 4 1/2" square poly bo
CourtEdge™ Reducers are threshold ramps designed to help make flooring transitions more accessible to individuals who use wheelchairs. These ramps can meet almost every floor transition requirement - from ½ inch up to 2½ inches in standard models, and custom heights exceeding 4½ inches. Made of 100% recycled rubber tire, CourtEdge™ Reducers have a slip-resistant surface and no load weight limitations. They are available in hundreds of configurations for interior and exterior use, and are pre-cut
The Curb Ramp is a portable ramp designed for use by people who have lower extremity or mobility disabilities or spinal cord injury and others who use a wheelchair. It is intended to help a person to get over curbs or uneven thresholds. Made from aluminum, the ramp is available with wheel guards on both sides, or with no wheel guards, allowing it to be used at a threshold where a door swings out. It has transition plates on both ends for a smooth entrance onto or exit off of the ramp. DIMENSIONS
The Dad0 Express Pocket Door is a motorized space saving door designed for use by individuals with mobility or severe disabilities or spinal cord injury. This modernized pocket door uses tempered Starphire glass and features a patented motorized system with advanced motion control. The glass door lies flush with any finished wall. The system features a pre-fabricated pocket door frame, a precision silent track, micro-processor controlled operation, and glass touch panels. Using a sensor, a maste
The Decpac Personal Mini Ramp, model MP24, is a portable curb or threshold ramp designed for use by individuals with mobility disabilities. The ramp is small enough to carry in a bag on a wheelchair and can be stored in a vehicle or at home. The ramp is made from laminated fiberglass. The top surface has a textured non-slip tread and the edges are marked with a caution stripe. The top edge is indicated with a label and has a thick, grooved rubber pad to hold at the edge of the step. The rubber g
The Decpac Personal Standard Ramp, model MP210, is a portable curb or threshold ramp designed for use by individuals with mobility disabilities. This ramp can be used to navigate over curbs or thresholds with a rise of up to 9 inches, and it is small enough to be carried in a bag on a wheelchair. The ramp is constructed from laminated fiberglass. The top surface has a textured non-slip tread, and the edges are marked with a caution stripe. The top edge is indicated with a label and has a thick,
Powered door operator with adjustable opening and holding times. Uses a DC motor. Can be retrofit to side opening doors. (No information on controls for operating the system.).
Door Butler is a door opener and door closer designed for use by individuals with mobility disabilities. This non-electric device utilizes a Red Thing non-slip hold-open tab to open the door to the position determined by the setting of the tab. The unit enables the individual to close the door while the tab is still engaged on the closer rod. To activate the auto open feature, the door is unlatched from the closed position, and the door automatically opens to the preset position. The door closes
DO IT YOURSELF ENTRY --- PURPOSE: To provide a means for individuals with arthritis or upper extremity, balance, or mobility disabilities to close doors. Included in a chapter entitled "Housekeeping & Getting Around," this article provides detailed instructions and illustrations for creating a door closer using basic materials. Screw eyes are screwed into the door and the doorframe and a heavy, smooth cord is tied to them. A heavy ring-shaped handle is tied to the end to the end of the cord
Door closer can be used on side hung, balanced door, interior or exterior. Can be mounted on push side, pull side, on jamb or on door. Hydraulic closer. Has adjustable sweep and latch speed, back check cushioning and closing force is optional, by model. Optional hold open arm, finished and metal covers. Standard parts and labor warranty.
The Door Finger is a door closing aid designed for use by people with mobility or lower extremity disabilities, spinal cord injury, and others who use a wheelchairwho have difficulty closing a door behind them. The unit is made of a light weight durable acrylic tube with a soft neoprene hand grip. A cord lock at the top allows it to fit around standard door knobs as well as door levers. With the cord looped around the knob or lever, the user can close a typical door by pulling on the tube. DIME
--- "DO IT YOURSELF" ENTRY ------- PURPOSE: Adaptation of a standard round doorknob includes a lever to make it easier to use by a person with hand weakness. Illustrates doorknob adaptation made with 2 round junction box covers, 2 1/2 inch bolts and nuts (4), and a strip of aluminum. One of the junction box covers has a slot cut to allow it to be slipped over the narrow part of the doorknob near the door; the other has a circle cut out of the center so it won't slip off the face of the knob. The
DO IT YOURSELF ENTRY --- PURPOSE: To enable an individual with limited grasp to opene a door. Form a loop large enough to fit over the door handle at one end of a length of parachute cord (available in hardware stores) Secure the loop around the handle and knot the remaining cord into a large loop to act as a pulling aid. MATERIALS: Parachute cord. AUTHOR: Labbe, A. TITLE: Quest Extra: Doing It Yourself. JOURNAL: Quest. WEB SITE: http://www.mda.org/publications/quest/extra/qe14-5_diy.html REF: V
The Door Hinge Expandable is a door hinge designed to widen doorway openings for wheelchair users. The hinge adds two inches to any doorway opening. The hinges are installed using existing hinge holes and screws. DIMENSIONS (LxW): 3.5 x 2 inches.
The Door Knob Gripper is a grasping aid for hand designed for use by individuals with arthritis of the hand or fingers or other grasping disabilities. Made of durable rubber, this round gripper slips over the existing knob minimizing hand stress.
The Door Knob Helper, model 640-8114-0200, is a door handle lever designed for use by individuals with grasping or upper extremity disabilities, arthritis, or other wrist or hand pain. The lever device is constructed of rubber and fits over most standard round door knobs. It is designed to eliminate turning or twisting of wrists and hands by enabling the user to press down on the lever to open a door.
--- "DO IT YOURSELF" ENTRY ------- PURPOSE: Loop on door handle to use forearm to open or close a door. A large loop of webbing or other strap is placed on a door handle to allow a poerson to use their forearm to open or close a door rather than using their hand. SKILLS REQUIRED: Sewing. AUTHOR: Lorig, K; Fries, J. TITLE: The Arthitis Helpbook: what You can Do For Arthritis. REF: Book: Addison-Wesley Publishing Co, Reading, MA: p 69. NARIC CALL NUMBER: R2178. 1979.
The Door Protection Kick Plate, model 194S, is a protective panel designed to protect a door from wheelchair-related damage. The plate is available in 0.05-inch gauge aluminum, brass, bronze, or stainless steel with six 0.63-inch truss head screws. OPTIONS: Self-adhesive tape; Spanner head screws; Torx head screws; counter sunk hole. DIMENSIONS: 8, 10, or 12 inches high, with custom width 2 inches less than door width.
DO IT YOURSELF ENTRYPURPOSE: To prevent children and adults with cognitive disabilities and poor impulse control from repeatedly slamming doors. This project was designed to prevent a child with Down Syndrome from slamming French doors, reducing noise and breakage. The solution was use 75 millimeter cabin hooks to hold the doors firmly against the existing white plastic door stops. The hooks were screwed to the skirting board behind the doorstops in a position too difficult for the child to rea
--- "DO IT YOURSELF" ENTRY ------- PURPOSE: Device to prevent door from closing completely. Inexpensive stopper to prevent door from closing and latching. A snap closing plastic shower curtain ring is wrapped around the edge of the door above the knob. The knob prevents the ring from slipping down the edge of the door. AUTHOR:Idea was in Better Homes and Gardens magazine. REF:Article. 1990.
The Doorknob Extender is a door handle lever designed for use by individuals with grasping disabilities. This door knob extension handle converts a standard doorknob into a door lever, providing extra leverage so less pressure is needed to turn the doorknob. The extender fits over a standard doorknob and allows access to keyholes. A cord or string can be inserted through the handle slot, making doorknobs easier to access for people with limited reach. DIMENSIONS: Handle length is 5 inches. COLOR
Door closer can be used on hinge hung door, exterior or interior, mounted on push side, pull side, on jamb or on door. Adjustable sweep speed, latch speed and backcheck. Can be set to meet interior barrier free requirements of 5 pounds maximum opening force. Optional delayed action and finishes. Covers standard. 5 year warranty.
Door closer can be used on interior or exterior doors. Can be mounted on push side, pull side, on jamb or on door. Adjustable sweep speed, latch speed, back check cushioning. Closing force can be set to meet exterior barrier free requirements of 8.5 pounds maximum opening force. Optional hold open arm and finishes. Delayed action optional. Standard with covers. 5 year warranty.
Surface applied hydraulic door closer with narrow 2 inch projection. Adjustable from sizes 1 to 4. Can be set to meet interior barrier free requirements of 5 pounds maximum opening force. Standard features include non-critical thermostatic sweep and latch valves, adjustable hydraulic backcheck, and flatform arm assembly. Delayed action optional. Mountings and accessories available for virtually any application. Five year warranty.
Full range surface applied hydraulic door closer with narrow 2 inch projection. Adjustable from sizes 2 to 6. Can be set to meet exterior barrier free requirements of 8.5 pounds maximum opening force. Standard features include non-critical thermostatic sweep and latch valves, adjustable backcheck, and flatform arm assembly. Delayed action optional. Mountings and accessories available for virtually any application. Five year warranty.
The Double Acting Door Pivot, model DAP-3, is a double acting door hinge that allows a door that normally swings inward to swing outward to reach someone who might have fallen in the path of the door. The hinge set includes extra heavy, finely finished top and bottom frame plates, with malleable iron top and bottom door plates, and can be used in conjunction with Stanley Emergency Stop, model ES-I, on commercial double acting interior doors weighing up to 135 pounds and up to 3 feet wide. OPTION
The Double Acting Hinge, model 463040, is a door hinge designed for use in the homes of individuals who are at risk for falls or medical emergencies. The hinge allows a door to swing in both directions, enabling a caregiver to open the door even if the individual has fallen against it. Fully adjustable spring tension returns the door to opening. This Class CD160-R hinge accepts doors from 0.38 to 1.38 inches thick and weighing up to 30 pounds. It comes with an adjusting rod, stop pin, and screws
Powered door operator for sliding doors. For single or bi-parting doors. Heavy duty, high pedestrian traffic volume system. Threshold activating and safety systems.
The DuraSwing MK 4R On-Demand Door Operator is a powered door operator designed for use by individuals with mobility disabilities. This door operator unlocks, power opens, holds open, power closes and re-locks doors. It can close doors automatically or on demand. It works with interior and exterior doors up to four feet wide that latch when closed, including wheelchair lift gates and elevator swing doors. It can operate in either an in-swing or out-swing configuration, can be configured for righ
The Duro-Matic Door Hinge is designed to provide easier access through narrow doorways for people who use wheelchairs. Replacing the existing hinges with these brass hinges adds two inches of clear space to the doorway. INSTALLATION: Uses the existing screws and holes.
The E-Z Pull Door Closer is a door closer designed for use by individuals with mobility or walking disabilities or spinal cord injury. This unit enables the user to close any size door behind him or her while using a walker, wheelchair, or mobility scooter. The device consists of a unit that snaps onto the door handle, and an acrylic hook that is applied to the door to pull it shut. WARRANTY: Lifetime warranty replaces any unit damaged through normal use.
--- "DO IT YOURSELF" ENTRY ------- PURPOSE: An extra handle is placed toward the hinge side of a door to facilitate closing it when an individual is in a wheelchair. A closed loop type of handle is installed in the hinge side of a door. Door closing can be initiated without going back into the doorway. SKILLS REQUIRED: Assembly. AUTHOR: Walter Zell TITLE: Household Items for Easier Living. REF: Journal article: Accent on Living, Summer 1980: p 62. 1980.
The Easy Gentleman Swing Door is a pneumatically opened & closed swing door operator kit designed to convert side-hinged doors to automatic doors to provide barrier free access for people with mobility issues. The converter allows manual use of the door by those not requiring the automatic opener. Designed for interior residential doors, this operator is mounted to the push side of the door and both sides of the cylinder are pressurized during the entire cycle. The standard includes the Pneu
The ED 800 Series Door Control is a door closer and powered door operator designed to provide the level of assistance required by the user for safe, barrier-free passage. The ED 800 is a combination surface closer and microprocessor-controlled electromechanical unit which continuously monitors door position, resistance, opening and closing speeds, and other variables, detecting the slightest deviation from the norm and responding appropriately. The unit functions as a standard door closer until
Exterior door. 42 inch wide door with balanced door type made of bronze, aluminum, wood, or stainless steel and tempered glass. Complete hardware included. Optional kickplate. Standard hardware accessible. Has a quick bottom rail height with optional power or manual closer.
EntryLevel Landings are accessible thresholds designed for use in commercial and public buildings to provide access for individuals who use wheelchairs. This modular, pre-fabricated unit is made from 100-percent recycled materials and is installed with high-grade adhesive to provide a solid door threshold transition. COLOR: The unit is available in color options that match the original substrate or to provide a visual color cue for pedestrian safety. DIMENSIONS: All models are 60 inches wide; av
Revolving door large enough to accommodate wheelchairs. Fully automatic, requires no pushing, pushbutton for handicapped or elderly use slows down the door to 50% of normal rotation speed (from 5-6 rpm's to 2-3 rpm's).
Panic bars come in wide and narrow style, including concealed and surface vertical rods, rim and mortise. All crossbar assemblies are brass, bronze, stainless steel, or steel.
"DO IT YOURSELF" ENTRY --- PURPOSE: To enable wheelchair users to close the door behind them. To make this door-closing aid, drill holes to install the eye hooks in three separate locations: at the top corner of the door,.at the inside top corner of door frame, and at the center of door frame. Tie one end of the rope to the hook on the door. Thread the rope through the hook on the top door frame. Thread the rope through the eye hook on the center of the frame. Attach a bracelet or other handle
The EZ Edge Ramp System, models RAEZ0010, RAEZ0020, RAEZ0030, RAEZ0040 and RAEZ0050, is a threshold ramp designed to provide access for individuals with lower extremity, mobility and walking disabilities, spinal cord injury and others who use wheelchairs. Molded under heat and pressure, these 100 percent recycled rubber, anti-slip ramps feature rounded front edges and molded traction pads and can be planed or trimmed to fit any doorjamb or uneven rise. The ramps may be installed using silicone
The EZ Open Door Latch is designed to aid individuals open screen doors. Features a paddle attachment to help push screen door latch. Slides over your existing screen door latch—no tools needed.
The EZ-Access Threshold Ramp is designed for persons with physical disabilities who use wheelchairs or scooters. The ramp provides smooth riding over doorway thresholds. Designed for most standard and sliding-door entrances, the ramp is made of durable extruded anodized aluminum and has a long, non-skid driving surface for maximum safety and support. A special finish resists dents and scratches. A flap attachment for sliding door tracks and installation hardware are included. Ramps accommodate t
The EZ-Close is a door opener and closer designed to make the process easier for individuals using crutches or a cane. The EZ-Close is a plastic-cup like structure that mounts to the door. It forms a pocket that you can place the tip of your crtch or cane into and pull the door opened or closed. This is ideal inthat is prevents a loss of balance from having to reach for the handle.
Ezyfold Door Control Arms is a door control system designed to create improved access and barrier-free living environments for persons with mobility and other physical disabilities. The system glides bi-fold doors, from cabinets to full size, smoothly, silently and dependably to and from their closed position. When the doors are open, rather than sticking out a 90 degree angle, these doors fold back a full 180 degrees agianst adjacent walls or cabinets and out of harms way. This feature improves
FireGuard Doors are accordian type fire doors designed to preserve the architectural beauty of large open rooms and foyers while offering protection from fire and smoke. These doors are placed in the wall, encased in mahogany frames and pocket covers, and are totally hidden from view. They allow one to follow building code requirements and fire safety standards without having to close off rooms or spend lots of money on renovations. The doors work on a patented track and trolley system that supp
The Flip a grip folding support handle is designed for individuals that have balance difficulties, anyone with poor special awareness, or those who need a little extra help walking through doorways. This product glows in the dark so it is visible in the dark when those with visual impairment may benefit from its use. It mounts on doorways or on the stairs or between a door and a screen door. Product can be folded away when not needed. Latex-free non slip grip.
The Genesys Series Grade 1 Cylindrical Lockset is a door lock with lever handle designed for use by individuals with grasping or upper extremity disabilities or arthritis. This door lock has a full length non-handed lever handle. It has a solid brass 6-pin keyway cylinder and fits doors from 1.375 to 1.75 inches thick, with fixed Thru Bolt Installation and concealed mounting screws. The housing is made from cold rolled steel and zinc dichromate finish for rust resistance with precision cast st
The Gentleman Automatic Swing Door Operator is a powered door operator kit designed to convert side-hinged doors to automatic doors, enabling access to those with mobility issues. The converter allows manual use of the door by those not requiring the automatic opener. The standard kit includes a Pneumatic opener, Hydraulic closer, Liftmaster MyQ wireless controls, Latch Release Kit, 100’ air tubing, 12 VDC Solenoid, 12 VDC Power Supply, compressor fitting, and mounting hardware. Each kit also in
The Pocket Gentleman Door Operator is a powered pocket door kit designed to provide barrier free access for people with mobility issues. Although pocket doors create more space for wheel chairs, without automation, many clients are unable to operate the door for desired privacy. The operator allows manual use of the door by those not requiring the automatic opener. This kit includes the custom pneumatic opener integrated with track, Liftmaster MyQ wireless controls, 100 feet of air tubing, 12 VD
The Glow In The Dark Gripper, model 16H162A, is an illuminated door knob gripper designed for individuals with low vision or fine motor or grasping disabilities. Exposure to bright light or sunlight recharges the power of this device. Illuminating power lasts up to eight hours keeping door knobs visible in a dark room for greater safety.
Great Grips are door knob or faucet covers designed for use by individuals with arthritis, grasping disabilities, or little or no manual dexterity or strength to open doors or turn faucets. These soft thermoplastic sleeves slip over existing rounded door knobs or faucets. Made of a soft latex-free material, they have a smooth surface to assist in turning. OPTIONS: Built-in AgION antimicrobial, a combination of silver ions bonded to a ceramic material called zeolite; built-in glow-in-the-dark cry
The Handi Lever is a cast aluminum retrofit door handle that converts existing conventional round doorknobs between 1 7/8 and 2 5/16 inches to lever style handles. The levers can be installed with an Allen wrench. No gripping or twisting is necessary to use the lever, and it is designed to not interfere with key locks or knob lock functions. SIZES: There are 7 sizes; right or left hand models. COLORS: Oil rub bronze, brushed chrome, antique brass, polished chrome, black, brass, satin brass, plat
The Handicap Revolving Door is an accessible door that is large enough to accommodate wheelchairs. The door system includes a floor mat or motion detector to start rotation of the door, an emergency collapsing door wing mounting, a button to slow rotation to half the normal speed, and an emergency power shut off.
Handicap Thresholds, Utility Thresholds, Rabbetted Saddles, and Traction Tread Thresholds are accessible threshold saddles in a variety of styles. The saddles are constructed of extruded aluminum, with an aluminum, bronze, or stainless steel finish.
The Handy Hook is an assistive door opener designed to help wheelchair users turn door knob locks and deadbolt locks. Doorways with limited access (i.e., a hallway) can create a barrier for many wheelchair users, prohibiting them from being able to enter or exit a location with ease. The Handy Hook solves this problem. It is a Multi-Functional Device that is capable of turning a door knob and opening a door from a distance that is clear of the door’s swing path, promoting greater independence fo
Automatic door closer. Unit is inserted in floor beneath door with lever arm attached to bottom edge of door. Separate latch and closing speeds. 3 options: non hold open, automatic hold open, and selector hold open. 8 1/2 pounds of force required to open door.
The Heavy-Duty Cylindrical
Lever Lockset, CL3500 Series, is a lever style security lockset designed for use by individuals with grasping or fine motor disabilities. This Grade 1 lockset has a through-bolted cylindrical chassis and solid cast levers with independent return springs to prevent lever sag. Two lever styles are available: Armstong, with a straight lever handle; and Newport, with a square-hooked lever handle. Available finishes are Bright Brass, Satin Brass, Bright Bronze, Satin Bronze
The Hero Threshold Ramp, models AA Thresh 1, AA Thresh 2 and AA Thresh 3, is an accessible threshold designed for use by individuals with mobility disabilities or spinal cord injury. This aluminum threshold ramp has an anodized, non-skid surface, and it is designed as a modular system in both the top surface and legs. DIMENSIONS (HxLxW): Usable area is 1 x 8.5 x 34 inches (AA Thresh 1); 2 x 14.5 x 34 inches (AA Thresh 2); 3 x 20.5 x 34 inches (AA Thresh 3). CAPACITY: 800 pounds. WEIGHT: 4 pounds
Powered door operator features 3 to 8 second adjustable opening time, side hung and balanced, exerts less than 15 pounds pressure, can be used on new or existing installations. Maximum door width 42 inches, maximum door weight 140 pounds. Power requirements are 115 volt 2.5A. Door opens to 90 degree angle, for exterior or interior use. Hold open time is adjustable 2 to 25 seconds. Door will stop if obstructed. In case of power failure, 15 pounds force needed to open, but force is adjustable. Has
Powered door operator for residential sliding door. Size: 3 inches by 3 1/2 inches by width of door. Opening speed adjustable, approximately 3 seconds minimum. Closing speed adjustable, approximately 4 seconds minimum. Hold open time delay, adjustable 1 to 15 seconds. Reverses if door contacts object during closing. Activated by push button switch. Optional: automatic locking, remote radio control.
The Inswing Exterior Door Threshold - Dark Bronze - ADA Compliant is an accessible threshold designed to modify a doorway to make it wheelchair accessible. A continuous dam provides a sill with a positive barrier to wind driven air and water infiltration, and helps maintain proper contact between the door bottom and sill for insulation and maintenance of the structure. Made of aluminum, the unit accomodates most single, hinged patio and french door systems configured with the door swinging inwar
The Jackson Mid Panel Exit Device is a panic bar that requires minimum pressure anywhere along the push section for activation. Designed for narrow, medium, and wide style aluminum doors. DIMENSIONS: 5 (h) x 24.5 (w) inches. UL approved for doors up to 48 inches wide. FINISHES: Available in dark bronze, black, and clear aluminum.
The Jackson Concealed Door Closer is a door closer with extra light springs. Models available for Center Hung, Offset Hung, Overhead Center Hung with extended spindle, and mechanism only.
The K-M Electrohydraulic Swinging Door Operators, Series 2000 is an automatic door operators surface mounted to the top jamb of new or exiting doors. They are completely self-contained with the electrohydraulic operator and controls mounted on a signal backplate and enclosed with an aluminum cover. The doors are available for single or double doors in any swinging configuration. Doors can be controlled to operate independently or simultaneously. Features include electrohydraulic power open and
The Keyless Doorknob Lockset is a keyless door lock designed for use by individuals with fine motor or grasping disabilities or arthritis. This solid brass lockset features a glow-in-the-dark electronic keypad that accepts up to six different entry codes of two to eight digits. Codes can be changed as needed. If an incorrect code is entered four consecutive times, an alarm sounds. This lockset replaces existing hardware and installs with the included mounting hardware. Two keys are included for
Keyless door lockset. Electronic pushbutton combination lock. Owner programs 5 digit master code, and secondary code which may be used to provide access to others and can be changed. Tamper alarm and keyboard lock activates when 16 random numbers are pressed. Stainless steel keyboard, weather resistant. Includes keyboard, control module, optional electric door strike, batteries, relay, cables, hardware and instructions.
Keyless door lockset. Electronic pushbutton combination lock eliminates the need for keys. Control module ($346 to $232) functions include 5 second unlock, 1 to 60 second adjustable shut, momentary or latching contact, and 25 second first touch relay. A five digit combination at the touchpad operates the system to unlock the door. 110 or 220 volt AC option, instant reprogramming at the touchpad, tamper alarm. 5 by 7 by 3 inches. Touchpad ($231 to $116) is waterproof, several finishes available w
The Keyless Lockset with Lever Handle is a keyless door lock designed for use by individuals with fine motor or grasping disabilities or arthritis. This solid brass lockset features a glow-in-the-dark electronic keypad that accepts up to six different entry codes of two to eight digits. Codes can be changed as needed. If an incorrect code is entered four consecutive times, an alarm sounds. This lockset replaces existing hardware and installs with the included mounting hardware. Two keys are incl
Kick Plates are protective panels of metal or acrylic plastic designed for use to prevent damage to doors from wheelchairs. Metallic plates have a brass, aluminum, or stainless steel base with a laquered, polished, anodized, or powder-coated surface. OPTIONS: Magnetic mount; adhesive mount. DIMENSIONS (HxW): 6 or 8 x 28, 30, 32, 34, 36, 38, 40, or 42 inches. Acrylic sheets are 0.13 inches thick. COLOR: Metalic plates are available with a polished brass, stainless steel satin, stainless steel pol
The Kwikset Delta Door Lever is an interior or exterior door lock with lever handle designed for use by individuals with grasping disabilities. This straight-blade-style lever handle is non-handed and is available with a keyed lockset for exterior use, a pushbutton lock for interior privacy use, or without a lock mechanism. COLOR: Lifetime brass, polished brass, antique brass, antique nickel, polished chrome, or satin chrome finish.
The Kwikset Dorian Door Lever is an exterior or exterior door lock with lever handle designed for use by individuals with grasping disabilities. This hook-ended lever handle is non-handed and is available with a keyed lockset for exterior use, a pushbutton lock for interior privacy use, or no lock mechanism. COLOR: Satin nickel, ifetime brass, polished brass, antique brass, antique nickel, Venetian bronze, polished chrome, or satin chrome finish.
Kwikset Signature Series Door Levers are lever door handles designed for use by individuals with grasping disabilities. Levers come in a variety of handle styles, including Ashfield, Avalon, Brooklane, Commonwealth, Pembroke, Lido, and Tustin. Most handle styles are curved, with or without scrolling. The Ashfield handle is straight and thick. Most styles are handed. Tustin is a reversible handle style that fits both right handed and left handed doors. The handle is available with a keyed lockset
DO IT YOURSELF ENTRY --- PURPOSE: To provide a means for individuals with arthritis, spinal cord injury, or upper extremity disabilities to open doors. Included in a chapter entitled "Housekeeping & Getting Around," this article provides detailed instructions and illustrations for creating a lever door handle. A pipe hanger bracket is attached horizontally to a doorknob with a radiator hose clamp. Prongs and sharp edges are covered with plastic tape. Plastic tape can also be used to cover th
CUSTOM ADAPTATIONPURPOSE: To enable an individual with upper extremity disabilities to open a residential fire door with an automatic closer. A lever made of lightweight aluminum tubing with rubber tips at each end was attached to the existing small lever handle with two hose clamps. This enabled the user to grasp the handle with both hands to turn it and use body weight to pull the door open. DIMENSIONS: The aluminum tube is 20 centimeters long. TITLE: Opening Gambit. JOURNAL: TAD Journal.
The Lever Handle Lock, model 2835, is a keyless exterior door lock with lever designed for use by individuals with fine motor, grasping, or upper extremity disabilities. This lock has levers on the inside and the outside, with a passage function that allows the outside lever to remain unlocked while the function is set. To enter from the outside while the door is locked, the user punches in the secret code, then pushes down on the lever. To exit, or to enter while the door is unlocked, the user
The Leveron is a door handle lever designed for use by individuals with grasping and other upper extremity disabilities. The device fits over conventional round door knobs to provide a lever handle and features an opening to allow full key access. The Leveron is constructed of high impact resin, fits left or right door openings, and is suitable for indoor or outdoor use. A plastic installation wrench is included. COLOR: Almond, antique brass, silver, dark bronze, and hi-glow white.
The Levon Door Handle is a lever door handle designed for use by individuals with fine motor or grasping disabilities. Designed for heavy-duty residential or light and medium-duty commercial use, it is available on inside only of deadlatch and keyed functions. The lever is zinc-based and brass, bronze, or stainless steel plated. DIMENSIONS: Length of lever arm is 2-9/16, 3-3/32, or 3-3/16 inches.
Life Safety Exit Devices are panic bars designed for use by individuals with grasping, fine motor, or mobility disabilities. Models include a panic bar with a surface vertical rod for wood and hollow metal doors (8100), a panic bar with a narrow stile surface vertical rod for aluminum doors (8200), a panic bar with a mortise exit device for wood and hollow metal doors (8300), a panic bar with a narrow stile mortise for aluminum doors (8400). a panic bar with a concealed vertical rod for hollow m
The LiteRamp Portable 1-Piece Wheelchair Ramp is a portable ramp designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury or others who use a wheelchair or scooter. The ramp has carrying handles, folds in the middle, and can be carried like a suitcase. It is made from aircraft aluminum, and it is fully covered with safety non-skid tape. This ramp is weather resistant so it can be left outdoor year-round. It is self-supporting to prevent slippage on sta
The M Series Mortise Lock with Levers is an exterior door lockset with lever handles designed for accessibility to individuals with grasping or fine motor disabilities. Levers are flat with an angled end. Right hand is standard, left hand optional. This heavy duty hardened steel lockset has a solid brass cylinder (5, 6, or 7 pin) and two stainless steel faceplates (armored faceplate in front). Heavy duty through-bolted inserts clamp the trim on the door assuring proper alignment. Two nickel silv
The Magic-Access Door Operator is a powered door operator designed for use by individuals with mobility or neurological disabilities or spinal cord injury. This unit can automate new or existing swing doors made of wood, metal, or glass. When the unit is installed, the door operates as a manual door with the option of activation from a pushbutton, wall-switch, or card reader. The Magic-Touch feature opens the door automatically when it is moved 3 degrees or more. The door opens under power and s
The Magic-Force Door Operator is a powered door operator designed for use in making commercial and public buildings accessible to individuals with mobility disabilities. The unit includes Magic-Touch activation, which can open a door when the user gives it a slight touch or push. The unit can be installed in supermarkets, department stores, hospitals, airports, office buildings, public buildings, schools, and universities, and is field selectable for full energy applications (ANSI A156.10), heav
The Maitre D'oor is a powered sliding door operator designed for use by individuals with upper extremity, mobility, or severe physical disabilities or spinal cord injury. This unit fits most sliding doors and can be used on existing doors with right- or left-hand openings. Features include six door speeds, six delay settings to adjust the time the door stays open before closing, a closing signal to alert to door closing, a doorbell for use when the door is in locked mode, and remote echo to aler
The Mini-Mullion Proximity Reader, model SXF1050, is a keyless door lock and security system. The system uses a credit card size command card, and does not require any contact between card and card reading sensor. The card does not have to be removed from wallet or purse to be read. The sensor is mounted on a mullion or narrow stile and has a reading range of up to 3 inches. The system has a tri-state LED visual indicator (red, green, amber) and provides audio feedback representing status and ac
The Motion Activated Door Key Light is a door lock light designed for use by individuals who have low vision. The unit has four bright LED bulbs that activate by motion to illuminate the keyhole, making is easier to find in the dark. Features include automatic shut off after six to eight minutes. The device mounts on the door with double-sided tape or screws (included). POWER: Uses 1 AA battery. DIMENSIONS (WxH): 3.125 x 1.5 inches.
The National Ramp Aluminum Threshold Ramp is a portable, modular ramp designed for use to make thresholds acccessible to wheelchair, walker, and cane users. This lightweight, durable, free-standing ramp can be placed indoors or outdoors in front of doorways, sliding glass doors, and raised landings. Made of anodized aluminum, the ramp is seam-free. The modular design with its interchangeable components accommodates thresholds from 0.75 to 6 inches high. DIMENSIONS: 34 inches wide.
The National Ramp Rubber Wedge Threshold Ramp is a portable ramp designed for use to make thresholds accessible to wheelchair users. The wedge is placed against the door threshold, either inside or outside, to provide a smooth ground-to-sill transition. Made of recycled tires, the ramp is slip resistant and portable. The ramp can be trimmed for lower heights and widths or combined to reach greater heights. For wider entrances, two ramps can be placed side by side. DIMENSIONS: 48 inches wide.
The National Ramp Rubber Threshold Ramp is a ramp designed for use to make thresholds accessible to wheelchair users. Placed in front of a door, it provides a smooth ground-to-sill transition. Made of 100 percent recycled materials, this portable indoor/outdoor ramp is slip-resistant and can be used on any surface. It can be trimmed or notched for a custom fit, and can be moved to any location. It does not interfere with door tracts, so it can be used with sliding glass doors. DIMENSIONS: 36 in
Off-Set Door Hinges are designed to widen doorway openings for access by wheelchair users. These hinges add two inches of width to the doorway and use the existing hinge holes and screws. DIMENSIONS (WxL): 2 x 3.5 inches. COLOR: Chrome.
The Offset Door Hinges, model 6523, are door hinges designed to allow the door to swing clear for greater wheelchair clearance. This hinge adds 2 inches to the door opening, using existing hinge holes and screws. Hinges are latex-free and come two to a package. DIMENSIONS (LxW): 3.5 x 2 inches. COLORS: Brass.
The Open Sesame System II is a residential powered door operator designed for use by people who use wheelchairs. The system includes the Open Sesame Deluxe Door Opener (Model 100), an electric strike plate for mounting in the wooden door frame, the wall transformer and wiring, the transmitter, and mounting hardware for inward and outward opening doors. The system opens and closes left- or right-side hinged doors with the touch of a button on the matchbox-sized transmitter which can be mounted on
The Otodor Swing Door Opener is a powered door opener designed for use by individuals with mobility, neurological, or upper extremity disabilities. Designed for non-professional installation (with the exception of the electric strike plate), this opener can be used on residential, office, or public restroom swinging doors weighing up to 100 pounds. Model DM-50 remotely opens and closes most interior swing doors. The kit includes the door opener main unit and remote control. Model DM-100 opens an
The Outswing Exterior Door Threshold - Dark Bronze - ADA Compliant is a threshold ramp designed for use to modify a doorway to make it wheelchair accessible. A continuous dam provides a sill with a positive barrier to wind driven air and water infiltration, and supports proper contact between the door bottom and sill for insullation and maintenence. Made of aluminum, this threshold accommodates most single, hinged patio and French door system configurations with the door swinging outward. DIMENS
The Outswing Exterior Door Threshold - Mill Finish - ADA Compliant is a threshold ramp designed to modify a doorway to make it wheelchair accessible. A continuous dam provides a sill with a positive barrier to wind driven air and water infiltration, and is conducive to proper contact between the door bottom and sill for insulation and maintenance of the structure. Made of aluminum, the unit accomodates most single, hinged patio and french door system configurations in which the door swings outwa
The Paddle Latch Operator, model 4590, is a door latch operator designed for use by individuals with fine motor disabilities. It is available for pushing or pulling to the left or the right with Adams Rite 4500, 4900, or MS+1890 series latches. SIZES: For door thicknesses of 1-3/4, 1-13/16 to 2, 2-1/4 to 2-1/2, 2-3/4 to 3, or 3-1/4 inches. Larger custom sizes are available. COLOR: Available with dark anodized bronze, black anodized, or satin aluminum anodized finish.
The Peephole Viewer is a peephole designed for use by individuals with low vision or seniors. The viewer pops into the existing peephole and features a liquid crystal display (LCD) panel for a larger, clearer, easier-to-see image. The unit compensates for "fish eye" distortion and has an anti-reverse feature so the user does not darken the peephole when moving up to the peephole. The unit offers regular and zoom modes. A base flange, a tightening tool, and a user's manual are included. POWER: Us
The Pemko Barrier-Free Ramp Threshold, model 257X259, is a modular threshold ramp designed for use to provide accessible thresholds for wheelchair users and individuals with mobility or walking disabilities. This ramp is available in cast aluminum, extruded bronze (brass), or anodized aluminum. OPTIONS: PemKote non-slip coating; cast aluminum wings (model WING10) that fit into each end of the ramp assembly and are fastened to the ramp mid sections with self-tapping machine screws. COLOR: Aluminu
The Pemko Modular Ramp Threshold Assembly for Flush Applications is a modular threshold ramp designed for use to make doorways and floor offsets accessible to wheelchair users and individuals with mobility or walking disabilities. The ramp assembly is made from mill finished aluminum. The number of assembly components is 1 (model R.5F), 2 (models R.75F and R1F), 3 (models R1.25F and R1.5F), 4 (models R1.75F and R2F), or 5 (models R2.25F). The assembly comes with with #10 stainless steel wood scr
The Pemko Recycled Rubber Ramp Assembly, model RR1.25FMR, is a modular threshold ramp designed for use by individuals with mobility or walking disabilities. It can be used at door thresholds or to transition between offset floors. The ramp has a diamond waffle pattern for traction. It can be field cut and coped, and is installed by gluing it to floor surfaces. The ramp is molded from 100 percent recycled rubber tires (20 mesh minus crumb reclaimed rubber with urethane binders). DIMENSIONS: 36, 4
The Portable Perfolite Fixed Ramp, models V5, V10 and E1, is a portable two-piece curb ramp designed to enable wheelchair users to get over curbs or steps. The ramp is made from perforated aluminum which does not allow the collection of rain, snow or dirt. It comes as a pair of single-piece tracks and includes a carrying handle. DIMENSIONS (LxW): 21.75 x 8.25 inches (V5); 45.75 x 8.25 inches (V10); or 41.75 x 10.5 inches. CAPACITY: 880 pounds per pair. WEIGHT: 3.5 pounds per ramp (V5); 7 pounds
The Power Access Automatic Door Opener, Model 4300, is designed to convert side hinged doors to automatic opening ones for people with disabilities. It is widely used for accessibility in schools and homes. This automatic door opener interfaces with environmental control systems and electric lock for door security. Activation controls include: touch plate, push button, push plate, radio transmitter, mats or momentary dry contact signals. Door opening pressure is adjustable; hold-open time is al
The Power Access Residential Door Opener, model 2300, is a powered door opener and closer designed for use by individuals with upper extremity or mobility disabilities or spinal cord injury. The unit fits in most interior and some exterior doors. Left- and right-hand door openers are available, and the hand is adaptable. The unit has a low profile to fit when there is limited room above the door. Safety features include the ability to be opened manually from either side; a friction clutch that c
The PowerMatic Door Operator, model 6900, is a powered door operator designed to make facilities accessible to individuals mobility disabilities. This unit automatically opens and closes with a lower energy opening force, and offers obstruction detection during both opening and closing cycles. It is handed and is available for either push- or pullside mounting,
Preso Matic Double Combination Lock, models DC9101, DC9102LT, & DC9200, is a keyless door lock designed for use by individuals with fine motor or grasping disabilities. These mechanically operated 4- or 7-digit combination locks are for in-or-out swing doors. Models DC9101 and DC9102LT are manually-locking deadbolt locks with a hardened steel free turning bolt. Model DC9200 is an automatic locking deadlatch lock with a hardened steel throw spring deadlatch bolt. DIMENSIONS: 5/8 inch bolt pro
Preso Matic Keyless Entry Lock, models 8101, LT8102, 8200, and 8200A, is a keyless door lock designed for use by individuals with fine motor or grasping disabilities. These mechanical keyless entry door locks are operated by pushbutton combination. The keypad has 10 pushbuttons, operated by pressing a 4 or 7 digit combination. The lock unlocks automatically when last digit is pressed. No knobs to turn or twist. Unlocks on the interior by pressing the unlock button. Models 8200 and 8200A have a d
The Prestige Series Wall Switches are designed to activate full- and low-energy powered doors for individuals with mobility or upper extremity disabilities. Available in a hardwired pushplate switch (model D33) or a wireless pushplate switch with a radio transmitter (model D33T), the switch provides switch closure at the door control and may be used with any powered door operator. The unit features a high-impact, textured polycarbonate plastic enclosure for weather resistance, better transmissio
The Silver Star Single Fold Ramp is a curb or threshold ramp designed for use by individuals with mobility disabilities. This lightweight, portable ramp has an integrated, high traction surface, and can be used to overcome a variety of obstacles at home and during travel. DIMENSIONS (LxW): 2, 3, 4, 5, or 6 feet x 29.5 inches. CAPACITY: 600 pounds. WARRANTY: 3-year transferable warranty.
The Pride SilverStar Solid Ramp is a ramp designed for use by individuals with mobility disabilities. This lightweight aluminum ramp has built-in traction control and side rails for safety, and is slotted for moisture drainage. It comes with securement components for mounting. DIMENSIONS (LxW): 1.5, 2, 3, 4, or 5 feet x 30 inches. CAPACITY: 600 pounds. WARRANTY: 3 year transferable warranty.
Door handle, aluminum or colors. Easily grasped push/pull with knurled or textured surface. Locking or latching available. Length 4 1/2 inches, diameter of pull 1 1/2 inches. 2 inches clearance from door surface. COLOR: Brass, zinc, or stainless steel finish.
The PVI Bariatric Threshold Ramp, models BAR1636 and BAR2436, is designed for use to make doorways accessible to people with mobility disabilities or spinal cord injuries who use wheelchairs. Made of aluminum, these ramps have an anti-slip, high traction surface, and there are holes punched in the top corners to facilitate installations. Hardware to secure the ramp to a surface is included. DIMENSIONS (LxW) 16 x 36 inches for thresholds 1.5 to 2 inches high (BAR1636); 24 x 36 inches for threshol
The PVI Rubber Threshold, models RAEZ0110, RAEZ1110, RAEZ1510 and RAEZ2100, is an accessible threshold designed for use by individuals with lower extremity, mobility or walking disabilities or spinal cord injury. Made of 100 percent recycled rubber, this threshold has a slip resistant surface, and it has no load weight limitations. It has molded miter ends, and it can be trimmed to fit a specific area with simple cutting tools. DIMENSIONS (DxW): 8.13 x 42 inches, with usable width of 36.25 inche
The Ramp Threshold - ADA, models 234A, 235A, and 236A, is an accessible threshold ramp designed for use with thresholds that are too high for easy wheelchair access. The ramp is constructed of extruded aluminum. DIMENSIONS (HxL): 0.5 x 3 inches (234A), 0.25 x 3 inches (235A), or 0.5 x 3.94 inches (236A).
DO IT YOURSELF ENTRY --- PURPOSE: To enable an individual with limited mobility to lock and unlock an entry door remotely. A door-lock solenoid from a car was mated to a standard dead-bolt. Power was connected through a momentary contact, center-off, double- throw switch that was wired to reverse the power polarity as it was moved up/down. This operated the solenoid in both directions. The switch was placed in box that was placed beside bed. The car-lock solenoid can be operated manually if need
DO IT YOURSELF ENTRY --- PURPOSE: To enablke an individual with only limited use of one arm to open her apartment door using a remote control while in bed. Because simply setting the remote on the bed would allow it to fall or slide out of reach, a holder was required that could be attached to the top bedcover and from which the remote can be easily removed for use during the daytime. The holder also needed to be easy to install and remove and be able to withstand frequent dropping as it would
The Retrofit Lever, model 04-032, is a lever door handle that converts D series Orbit, Plymouth, and Tulip design knob locks into lever handle locks. Conversion can be made without removing the lock from the door. Black, engineering grade resin designed for high usage on all standard door installations. Lever returns to within one half inch of face on 1 3/4 inch doors. Converts both keyed and non-keyed D series locks.
---- PROTOTYPE --------- PURPOSE: To create a powered, remotely operated door opener for a high school locker for a student with muscular dystrophy. A pair of seniors, Micah Stuhldreher and Wyatt Smrcka, in a robotics class at Pinckney Community High School in Michigan used their school's resources to build a device that allows their classmate with muscular dystrophy to open his locker using a remote control from his wheelchair. Working with their robotics teacher, they fabricated moving parts a
The Rubber Doorknob Extension, model 6393, is a door handle lever designed to assist individuals with limited manual grasping ability. The handle's soft rubber molding snaps over the doorknob, providing leverage to turn the knob. Fits knobs 2 to 2.5 inches in diameter. Latex free. DIMENSIONS: The handle is 2.5 inches long.
The Rubber Threshold Ramp is an accessible threshold designed to provide wheelchair or scooter access in entryways. To provide a smooth and secure transition, the ramp is positioned against the door threshold. The rubber can be trimmed to fit the doorway, and ramps can be stacked for higher rises. DIMENSIONS (HxLxW): 1.5 x 14 x 36 inches, 2.5 x 24 x 48 inches, or 4.75 x 48 x 48 inches. CAPACITY: 850 pounds. WEIGHT: 18 pounds (1.5 inch rise), 40 pounds (2.5 inch rise), or 127 pounds (4.75 inch ri
The Saddle Threshold, model 713, is a threshold ramp designed for use by people with mobility, lower extremity or walking disability. This door threshold is available with an aluminum, bronze, or stainless steel finish. It has a non-skid surface and is available with an abrasive coating. DIMENSIONS (HxW): O.3125 x 4.5 or 7 inches. Typical wall (top plate) 0.125 inch, CAPACITY: 0.74 pounds per foot at 5 inches to 1.01 pounds per foot at 7 inches.
The Saddle Threshold, model CR3715, is a threshold ramp designed for use to make carpet transitions accessible to wheelchair users. This heavy duty and durable threshold is available with a mill finish. The unit is drilled for screws (Included). DIMENSIONS (HxLxW): 0.25 x 36 x 5, 0.25 x 48 x 5, 0.25 x 72 x 5, or 0.25 x 96 x 5 inches. COLOR: Aluminum or dark bronze.
The Saddle Threshold 1 is a threshold ramp designed to provide wheelchair access in doorways. The mill finish bronze and stainless steel thresholds have a smooth surface; aluminum thresholds have a fluted surface. The threshold comes with ten 1.5-inch wood screws. OPTIONS: Sure-Step non-slip abrasive coating; other screw types and anchors. DIMENSIONS (HxW): 0.31 x 2.5 inches (model 401S); 0.5 x 3 inches (model 402S); 0.25 x 4 inches (model 403S); 0.5 x 4 inches (model 404S). COLOR: Available in
Electronic door closer provides door control for single or double smoke and fire barrier doors. Holds door open under normal conditions providing unobstructed traffic flow. Closes door automatically in a smoke or fire emergency. Does not require the use of hands to clsoe door.
Schlage Levers are door handle levers designed for use by individuals with fine motor or grasping disabilities. Levers are available in eight different styles (Accent, Avanti, Callington, Champagne, Elan, Flair, Jazz, or St. Annes) and 10 different finishes to fit the user's home decor. The same unit can be used as either a right- or left-hand lever. OPTIONS: Elan or Jazz style lever on keypad lockset. COLOR: Bright brass, antique brass, satin nickel, bright chrome, satin chrome, antique pewter,
Lever style security lockset door handles. 20 degree turn will operate 0.5 inch throw or 1 inch deadbolt tested to 1000 pounds torque. Bronze or stainless steel. Meets ANSI grade 1 requirements. Straight and return level designs available. Some models with interior security bolt. Keyed lock in handle.
The Self Supporting Adjustable Threshold Ramp, models ATH1232 and ATH2432, is a ramp designed for use to make doorways accessible to wheelchairs for individuals with mobility disabilities or spinal cord injury. This ramp is designed for doorways that swing out or in, and its height is adjustable to fit a range of threshold rises. The unit aligns directly against the door threshold. Made of welded aluminum, it has a slip resistant grooved surface and accommodates wheelchairs and scooters with va
The Self Supporting Threshold Ramp, models SSTH1636-1.5, SSTH2436-2, SSTH2436-2.5 and SSTH2436-3, is an accessible threshold designed to provide wheelchair access for doorways to individuals with mobility disabilities or spinal cord injury. This threshold ramp can be used in doorways with doors that swing out or in. It has an anti-slip, high-traction surface, and it is made of aluminum with durable, welded construction. DIMENSIONS (LxW): 16 x 36 inches with 1.5-inch rise (model SSTH1636-1.5);
The Senior Swing Door System, 4663 Series and 5663 Series, are electric powered door operators for interior or exterior doors. The door operator is available in overhead or surface applied housing. There are two modes of operation: handicapped or manual mode. In the Handicap mode, the door is actuated by pushing a button on either side of the door. The door opens slowly to back check in 3 to 6 seconds and to a fully open position in 4 to 7 seconds. The door remains open 5 to 30 seconds in preset
Door closer can be used on side hung door, for interior or exterior, mounted on pull side on door. Spring powered closer, adjustable sweep, latch speed, and backcheck. Spring power adjustable to increase power by 50 percent. Handling must be specified. Optional hold open arm, fusible link, finishes, metal cover. Ten year warranty on parts. Has built in delayed closing feature that delays the closing of the door up to one minute. Adjustable to fifth opening force.
Door closer can be used for interior or exterior on side hung balanced door mounted on push side jamb. Spring powered closer has adjustable sweep speed, latch speed and backcheck. Optional hold open arm, fusible link, finished, metal cover. 10 year warranty on parts. Has built in delayed closing feature that delays the closing of the door up to one minute. Adjustable to fifth opening force.
Door closer can be used on side hung door, interior or exterior. Spring powered closer is mounted on push side of door and has adjustable sweep speed, latch speed and backcheck. Spring power adjustable to increase power by 50 percent. Optional hold open arm, fusible link, finishes and metal cover. 10 year warranty on parts. Has built in delayed closing feature that delays the closing of the door up to one minute. Adjustable to fifth opening force.
The Stand Alone Threshold Ramp is an accessible threshold designed to make a doorway or single- step rise accessible to wheelchair or scooter users. The threshold has adjustable legs with a two-inch range, which can be helpful for locations where the surface is uneven, such as decks or turf. The ramp is made of aluminum or painted steel with a non-slip button or expanded metal surface. Safety side curbs are cut level to the top of the threshold allowing a door to open over the ramp. DIMENSIONS (
The Standard Threshold Ramp, models THR832, TH1032, TH1232, TH1632, TH1636, TH2432 and TH2436, is a threshold ramp designed to make doorways accessible to wheelchairs for individuals with lower extremity or mobility disabilities or spinal cord injury. The ramp has holes punched in its top corners so it can be secured to the surface of the doorway using hardware that is included with the ramp. The unit is made of lightweight, durable aluminum with an anti-slip, high traction surface. DIMENSIONS (
The Stanley AccessPro is a powered door operator designed for use in long-term care, rehabilitation, assisted living, and health facilities. This system provides automation of new or existing manual doors. The system unlocks, opens, closes, and relocks doors at the touch of a button. Up to 15 remote controls can be programmed to one door system. Keyed access and manual operation remains intact. Operation stops when an obstruction is encountered. The system includes a motor/gear box attached to
The Stepless Excellent Doorstep Ramp Kits, models 100, 101, 102, 103 and 104, is a threshold ramp designed for use to make doorway thresholds accessible to wheelchair users or individuals with walking disabilities. Each ramp has three layers, of which the two upper layers are loose for adjustment in height. The ramp in Kit 100 can level differences from 0 to 0.875 inches; Kit 101 is for differences from 0.875 to 1.625 inches; Kit 102 is for differences from 1.625 to 3 inches; Kit 103 is for diff
The Stepless Excellent Doorstep Ramp Kits 0, 1, 2, 3, and 4, models 11-12100, 11-12101, 11-12102, 11-12103, and 11-12104, are ramps designed for use to make doorway thresholds accessible to wheelchair users and individuals with walking disabilities. Each ramp has three layers, of which the two upper layers are loose for adjustment in height. The ramp in Kit 0 (11-12100) can level differences from 0 to 0.875 inches; Kit 1 (11-12101) is for differences from 0.875 to 1.625 inches; Kit 2 (11-12102)
The StoneCap Rubber Threshold, models STC0110, STC1110 and STC1510, is an accessible threshold designed for use to make doorways and room entrances accessible for individuals with lower extremity, mobility and walking disabilities or spinal cord injury. Made of 100 percent recycled rubber, the threshold has a slip resistant surface, and it has no load weight limitations. It has molded miter ends, and it can be trimmed to fit a specific area with simple cutting tools. OPTIONS: Grooved surface ava
Door closer can be used on side hung, balanced door, for interior use. Spring powered closer mounts on push side, pull side, on top jamb (push side only) or on door. Has adjustable sweep speed, latch speed and back check. Opening force 3 to 8 pounds. Optional hold open arm, finishes and metal cover. 10 year warranty on parts.
The Clear Swing Door Hinges are offset hinges designed to allow the door to swing clear of the opening, permiting greater width for wheelchair access.
Tactile Warning (Knurling) is a coating option for door lever handles, designed for use to identify potentially hazardous areas such as electrical closets and mechanical equipment rooms for individuals who are blind or have low vision. Knurling is available in SAT design levers only from Schlage. Outside lever only is knurled unless otherwise specified.
The Threshold Ramp is an accessible threshold designed to enable wheelchair users to get through dooways and over thresholds. This low profile aluminum unit can adapt a doorway or threshold from 1 to 4 inches in height. Its top lip seamlessly covers the existing threshold for a smooth transition. The ramp is constructed from welded aluminum with a permanent skid resistant surface, and can be used indoors or outdoors. DIMENSIONS (LxW): 6, 12, 18, 24, or 36 x 30 or 36 inches. WEIGHT: 6 to 28 pound
The Threshold Ramp - Lego Style is a threshold ramp designed for use to make doorways accessible to wheelchair users and individuals with mobility or walking disabilities. The ramp is lightweight, and it allows water to flow through so it can be used outdoors, in a bathroom or other environments in which the floor or ground may get wet. It has a non-slip surface and can be used on both the inside and outside of the doorway for rolling over the threshold. It accommodates most doorway entrances in
The Touchless Switch is an active infrared proximity sensor powered door operator designed to provide hands-free activation of full- and low-powered doors, clean room access points, request to exit devices, and point of purchase displays for individuals with upper extremity and mobility disabilities. This device activates a powered door when an individual passes the motion sensor and employs a coded carrier infrared signal to produce the proximity pattern. An incorporated microprocessor produces
The Trimco 1-1/4 Inch Diameter Door Pull is a door pull designed for use by individuals with grasping disabilities or limited upper extremity strength. The pull handle is round and extra-wide for better grip. OPTIONS: Mounting hardware; fOCAL Series styling. DIMENSIONS: Length is 13.25 inches (model 1195-3J) or 19.25 inches (model 1195-6J). Projection is 3.5 inches and clearance (the distance between the door and the pull) is 2.25 inches. COLOR: Brass, bronze, aluminum, platinum, or stainless st
The Trimco 1-1/4 Diameter Offset Door Pull is a door pull designed for use by individuals with grasping disabilities or limited upper extremity strength. The pull handle is round and extra-wide for better grip, and is offset from the points of attachment to the door. OPTIONS: Mounting hardware; fOCAL Series styling. DIMENSIONS: Length is 13.25 inches (model 1191-4J) or 19.25 inches (model 1191-5J). Projection is 3.5 inches, offset is 5 inches, and clearance (the distance between the door and the
--- "DO IT YOURSELF" ENTRY ------- PURPOSE: Adapted door knobs provide additional leverage for those with limited hand function. Two door knob adaptations are described. The first involves drilling a hole in a crutch tip using a drill bit, inserting a small wooden rod, wrapping the ends of the rod with rubber or electrical tape and placing the crutch tip over the doorknob. The second model involves simply putting a crutch tip over the doorknob to increase the surface area. SKILLS REQUIRED: Assem
---- PROTOTYPE --------- PURPOSE: To design a door handle that pushes or pulls to open an interior door making it possible for individuals with disabilities, small children, or anyone unable to use either or both hands to enter and exit through the doorway. The UltraLatch doesn’t twist or turn like traditional door handles. The user unlatches the door by pushing or pulling UltraLatch approximately .5 inches. Inspired by the auto gear shifter, the UltraLatch is designed to conform to the shape of
---- PROTOTYPE --------- PURPOSE: To create a prototype of universal lock that allows children with disabilities to operate a school locker. In middle and high school, almost every student secures their locker with a dial combination lock. Individuals with cerebral palsy or spinal cord injury may be unable to use these types of locks due to a lack of motor or cognitive skills necessary to open a standard lock. A universal lock prototype was created and tested on children with special needs. The
The Vivo! Controller is an environmental control unit designed for use by individuals with mobility or severe physical disabilities or spinal cord injury. This wheelchair-mountable unit is configurable to control the environment, make telephone calls, answer and unlock the door, or contact caregivers. It has more than 1,000 functions, and can operate as a remote control with infrared or radio control output, or as a wired switch control with one or two switch scanning methods. It has a full colo
Panic device for doors, easily grasped, lever trims, knurled or textured surfaces, locking or latching available. Width of door 30 to 48 inches, 15 pounds of force required to operate device. Customizing optional.
The Yale 5400LN Series Heavy-Duty Cylindrical Lockset, is a door lock with lever handle designed for use by individuals with grasping, fine motor, or neurological disabilities. Designed for industrial, commercial, and institutional use, features include Yale 6- and 7-pin standard and interchangeable core cylinders; stainless steel latchbolt with direct half-inch throw; wear-resistant chassis plates; heavy-duty lever return springs to prevent lever sag and provide positive return of lever to